This is a clone of the Univox Super Fuzz. I built a few of these here. This one uses a matched transistor pair: LM394CH. I thought this would enhance the octave effect since matched transistors enhance this effect. Seems like this circuit likes low gain transistors in the rectifier. The LM394CH is a high gain … Read more
This is a second version of the Univox Super Fuzz. Check out the first version in these posts. The first version fit a 1590BB sized box. This time I thought I’d try and get it into a smaller 1590B box (this is my favorite size). This worked pretty well but jacks and footswitch are a … Read more
Another Super Fuzz build. I used the first PCB I designed from a post over at FreeStompBoxes.org, read about that first build here. This one looked good but it didn’t work! I put it aside because the problem wasn’t obvious. I got it out again and set at debugging. After a few minutes with the … Read more
Build your own Super Fuzz! The Super Fuzz is an octave fuzz used by Pete Townsend, Muddy Honey, J. Mascis and others. Read this post to learn more about the Super Fuzz. Build Your Super Fuzz Here is the schematic for the Super Fuzz. Note! There are several versions and schematics vary. This schematic matches … Read more
Super Fuzz is a circuit that has many variations. It’s one of the popular building blocks that has been used for decades. It’s built around a full wave rectifier that produces an octave fuzz sound. similar circuits that use the full wave rectifier: Super Fuzz Kay Fuzztone Univox Super Fuzz Honey Psychedelic Machine Third Man … Read more
I updated the Super-Fuzz Board to fix a problem with the last version. The prototyping service at PCBWay.com is very inexpensive, which facilitates my workflow. The schematic I used for this project came from Freestompboxes.org. It’s based on the original with a couple mods. The Tone switch has been turned into a pot to provide a range … Read more
I have this bag of NPN Germanium transistors. These are rare and you don’t see them much in pedals. They offer a huge advantage over the typical PNP types found in Fuzz Face’s, you can use a regular power supply! PNP Fuzz Face must use a reverse power supply, the + and – are switched. … Read more
This is an NPN Germanium Fuzz Face. I designed the PCB in Eagle, and had the PCBs made at OSHPark.com. The original Fuzz Face used germanium PNP transistors. The germanium transistors is supposed to have some special mojo. PNP types are more common but require either a battery charge pump to create a reversed power … Read more
The next pedal building workshop at Noisebridge will be about building a Fuzz Face. If you’re in the bay Area check out the workshop on meetup! the Fuzz Face is a classic fuzz circuit with a bit of magic. its one of the earliest fuzz circuits to be developed, it has been played by many … Read more
I built this a few years ago. I got it out and played it for a while. sounds pretty good. This is a Big Muffin with a diode lift switch, and a blend control. The PCB is from https://shop.pedalparts.co.uk/product/bassblendmuff. It worked well but the board doesn’t have an LED! So the wiring is a little … Read more
The Fuzz by Retro Channel is a Fuzz circuit built around the CA3046 transistor array. It’s a lot like a Fuzz Face and Tone Bender. It makes use of all of the transistors on the CA3046 and sounds pretty good doing it. Here is a schematic I found over at https://www.freestompboxes.org/viewtopic.php?t=13062 Q3 and 4 are … Read more
I have wanted to try the Frantone Peach Fuzz for a long time. The circuit uses one of my favorite chips the LM386. Not only does it use the 386 it uses two in series. Frantone is one of the original boutique companies, starting in 1994! They went dormant for a some years but have … Read more