Super-Freq » Schematic

Axe-o-Matic

admin — Sat, 05 Jun 2010 04:44:30 +0000

Here’s a new drawing from the Stompbox Cookbook. This is a passive mid control. Could be a good alternative to the standard Guitar treble roll off type tone control. The pot should be a dual gang linear.

Axe-o-Matic

Ring Mod

admin — Sat, 18 Jul 2009 15:07:37 +0000

Here’s an idea for a ring modulator. I used a 3080 for the balanced modulator from the Ring-Modu-Matic. I used an envelope, from the Meatball, to control the carrier frequency.

This is untested. The controlling the FET to turn on the carrier is going to be a challenge.

Ring Modu-Matic take two

admin — Sat, 04 Jul 2009 01:50:38 +0000

There were a few mistakes in the last version of this. Here’s an updated schematic and PCB.

Ring Modu-Matic

admin — Fri, 12 Jun 2009 06:49:13 +0000

Here’s a PCB and Layout for the Ring Modu-Matic. I have yet to build this yet so use these files at your own risk! The dual gang pot in the lower corner I can’t get rid of, due to my lack of skills with Eagle. Notice the lines connecting the pot to pads on the PCB.

*** edit: These schematic and PCB had some errors. It’s been removed. There is an updated version the next post ***

Tremolo FX Loop

admin — Sat, 06 Jun 2009 20:26:20 +0000

This is a first draft of an idea that I have been thinking about for a few months. It’s a Tremolo that pans between the input signal and the signal coming through the FX Loop. If no signal is coming in to the FX Loop it would act as a normal Tremolo. Otherwise it would be cycling from the straight to the effected signal.

The main idea was taking from Nicolas Boscorelli’s Stompboxology Tremolo-Matic X. I make no gaurantees that this actually works as I haven’t built it. This is just a first pass to get the idea down.

Tremolo-Matic X

admin — Sat, 06 Jun 2009 05:03:48 +0000

This is Tremolo-Matic X from the Tremolo Issue of Stompboxology by Nicolas Boscorelli. I have redrawn the schematic to make it easier to read. Hopefully this will be helpful to anyone attempting this project. This is Tremolo that pans between a treble and bass signal. It inlcudes controls to set the level for both the bass and treble, rate and depth.

I built mine from the PCB layout posted by Morocotopo at Diystompboxes here. This lay out worked well for me. Though it looks likes it isn’t finished as there are a few extra pads that don’t quite make sense. The layout does work. I have built it myself.

It sounds pretty good. I made a few changes. First I changed the Rate pot to 100K to get a more useable range of speeds. With the original 25K pot the slowest speed was not very slow. I like the sound of slow tremolo. The 100K pot is shown on my vsersion of the schematic. speaking of the rate, I’d like to get a slightly faster rate at the fast speed and a little slower at the slow end. I think I will be playing with R21, R25 and C15 a little more.

The other mod, not included in my schematic, is to decrease the gain on the input stage. Basically this comes down to decreasing the value of R14. With the original value of 470K you get a little bit of clipping with hot pickups. I haven’t decided on a value yet.

Note the, input stage is inverting. Which presents a lower input impedance than would normally be acceptable. But it seems to work OK here.

Also note that there are a few parts list as optional feed through bias or something like that. These parts include a 5V regulator and adjacent parts. I left these out of my build, and everything worked fine. I left these out of the schematic posted here.

Revolting Visage

admin — Mon, 13 Oct 2008 22:26:09 +0000

Here’s my take on the Ugly Face/Crash Sync. I took my favorite parts of both and a few suggestions from RunOffGroove and the DIYStompboxes forum.

This version uses a different input buffer, which more closely resembles the input of the Crash Sync. Though it has a greater gain. I found this gave more sustain. The Ugly Face has a gain of about 200. The Revolting Visage uses a gain of about 1000.

I took the envelope from the Ugly Face which is simple and elegant and seems to work well for this design.

I also borrowed the Threshold from the Ugly Face. Which allows for self Oscillation.

These last two features do not exist on the Crash Sync. But, are a lot of fun to play with.

I changed the output to be directly taken from pin 3 of the 7555. The Ugly Face used a strange arrangement that was also connected to pin 7. The pin 3 arrangement makes more sense to me and is simpler.

MOSFET Boost Layout

admin — Wed, 30 Apr 2008 19:42:04 +0000

Here’s a layout for the MosFET boost. The drawing is pretty sloppy. But this shows the schematic and layout I used for my build. Seemed to work well.

Here’s a link to a picture of my build. Here’s a link to the schematic on Muzique.com

9V Sample and Hold

admin — Sun, 16 Mar 2008 20:02:33 +0000

Here’s a sound sample of the 9V Sample & Hold I have been working on. So far things are going pretty well. It’s based on an idea by Brian Marshall and the Color Sound Wah.

9V S&H Test Mp3

Sample & Hold

admin — Sat, 01 Mar 2008 21:26:48 +0000

I have this for Sample and Hold effects. Though I have yet to build a really good one.

Here are a bunch of sketches of S&H ideas that I have been testing.

This is the Maestro FSH-1.

This uses a 7555 timer for a clock in an attempt to get as short and sharp a clock pulse as possible.

This is Ray Wilsons Sample and Hold from Musicfromouterspace.com

Here’s an idea from the app notes of the 13600. This one worked pretty well.

This idea came from the Diystompbox.com forum