-
22/7 4069
First build of 2022! This is a 4069 version of RunOffGroove’s 22/7. The original uses the 4049 hex inverter. This the same circuit using the 4069. Both chips contain 6 inverters but the they differ in format and layout. The 4049 is a 16 pin DIP and the 4069 is a 14 pin DIP. One…
-
AionFX Quadratron LoveTone Doppelganger clone
I always build three of everything. I got three of these boards when AionFX released them. I built one and gave it away. I’m finally getting the other two finished. This is not straight clone of the Doppelganger it has some changes that are updates and improvements, and a few changes that are opinionated. Read…
-
Tim Escobedo’s PWM
Tim Escobedo was this wildly creative force in the early DIY Stomp Box community. His circuit snippets page was had a lot of really great ideas. One of the ideas there was the PWM, which stands for pulse Width Modulation. This circuit converts your input signal into a square wave and varies the amount of…
-
UBE Screamer 4069
This is a version of the UBE Screamer using the 4069 in place of the 4049. Essentially these chips are the same. They both contain 6 inverters. The 4049 is a 16 pin DIP while the 4069 is a 14 pin DIP. Electrically the should the same but the pin arrangement is different. The original…
-
22/7 4069
Here is a version of RunOffGrooves 22/7 using the 4069. The original circuit uses the 4049 Hex inverter. The 4049 is a 16 pin dip with 6 inverters. Here is the 4049UBE data sheet. You can see it has 16 pins with 6 inverters. There is a power Vdd pin 1 and ground Vss pin…
-
Another fail!
Here is a UBE Screamer with blend knob. I left a resistor out of the mixer and mixed up the Blend and Gain labels, double fail! As long as I’m going to screw things up I like to go all the way! This enclosure looks good! I like the logo outline and the pot labels…
-
UBE Screamer v2
I made an update to the RunOffGroove UBE Screamer from a suggestion in their notes. This version adds a mix control the blends some of the original signal with the distorted signal. The original uses Rx to set a fixed mix amount. The notes suggest a value of 100K to 470K for this resistor with…
-
Weston Audio AD110
I built this as a DIY project. They offer it assembled also. It’s a Eurorack adaptation of the drum sounds from the Boss DR-110. All the sounds are analog, not samples. The project comes as three PCBs and a front panel. It’s all through hole parts. The parts are fairly easy to get. I few…
-
PCBs with pots and LED
I just built a PCB project without the LED taken care of on the board, what a headache! In the old days everything was like that but we have evolved since then! in my most recent projects I have been following the layout used by PedalPCB. I feel like they have hit on an arrangement…
-
1981 Inventions DRV clone.
Here’s a PedalPCB Informant. This is mostly the Rat circuit with a few changes. The biggest change is the addition of a charge pump. The charge pump provides a +9 and -9 volts power for the circuit to run off. Effectively this doubles the voltage. I have some reservations about the power supply. The clipping…
-
Serge Resonant EQ
This is the last piece of musical gear for the year. It’s a fixed filter bank with 10 filters. 8 of the filters are bandpass filters. The highest and lowest bands are high pass and low pass filters. It’s like a 10 band equalizer with synth filters. The filters are tuned to major sevenths and…
-
UBE Screamer 1.1.1 build
Built and tested the new version of the UBE Screamer PCB. Everything is working! Sounds great. This is a good alternative to the standard TS-808 and other overdrives if you’re looking for something a little different. Does great low gain sounds. I built this in a 1590B enclosure from Tayda. I got most of the…